DIY Pendant Light

Last Updated on March 3, 2022

WOW! This is amazing! Learn to make your own DIY pendant light using your own fabric! Full tutorial by Designer Trapped in a Lawyer's Body.

Hello lovely readers! I am BEYOND excited to share today's project with you. I am going to show you how I made a DIY pendant light for my craft room/office with the help of a seriously amazing lighting kit and some other basic supplies. But first, a bit of background…

You may remember that I revealed my craft room/office back over the summer. This post contains some affiliate links. Click here to read my full disclosure policy.

MUST PIN! Craft room reveal full of awesome craft room ideas! #craftroom

As you can see, the room included that SUPER fun and funky light fixture that I purchased at Ikea. The problem is that I use my craft room A LOT at night after my girls have gone to bed and that super fun light did NOT give off enough light for the room. So, our love affair ended almost as quickly as it began {don't worry, I have another plan for that light}.

Fast forward several months…I was so excited to learn about a brilliant product called I Like That Lamp.

WOW! This is amazing! Learn to make your own DIY pendant light using your own fabric! Full tutorial by Designer Trapped in a Lawyer's Body.

It is a kit that contains all you need to create a custom drum lampshade using your own fabric. You can purchase a variety of sizes directly from I Like That Lamp; a limited selection is also available on Amazon.

Though it is typically intended to make shades for table and floor lamps, I knew I could easily use it to make a DIY pendant light as well. And guess what?! It worked perfectly. Read on to learn how I did it!

 DIY PENDANT LIGHT TUTORIAL

Materials Needed:

WOW! This is amazing! Learn to make your own DIY pendant light using your own fabric! Full tutorial by Designer Trapped in a Lawyer's Body.

Steps:

1) Assemble the drum shade. I highly recommend you watch this YouTube video.  It will help immensely. Below is my tutorial along with step-by-step photos.

  • First, iron your fabric very well so that no seams or creases remain.
  • Next, lay your fabric out UPSIDE DOWN on a flat surface and remove six inches or so of the backing from the styrene and place the sticky side of the styrene on the fabric. Slowly remove the rest of the backing while you are sticking the styrene to the fabric. Be sure to leave 1/2 inch of fabric overhang on each side and the end.

WOW! This is amazing! Learn to make your own DIY pendant light using your own fabric! Full tutorial by Designer Trapped in a Lawyer's Body.

WOW! This is amazing! Learn to make your own DIY pendant light using your own fabric! Full tutorial by Designer Trapped in a Lawyer's Body.

  • Next, cut away the excess fabric. Again, be sure to leave 1/2″ overhang on each side except for one short side.

WOW! This is amazing! Learn to make your own DIY pendant light using your own fabric! Full tutorial by Designer Trapped in a Lawyer's Body.

  •  On the one short end where you left some fabric overhang, fold the overhang over the styrene and glue it down. The glue is included in the kit.

WOW! This is amazing! Learn to make your own DIY pendant light using your own fabric! Full tutorial by Designer Trapped in a Lawyer's Body.

  • Stand the styrene up and shape it into a lampshade. Place your top lampshade ring {the one with the finial attachment hole} into place, using the included binder clips to hold them in place.
  • WOW! This is amazing! Learn to make your own DIY pendant light using your own fabric! Full tutorial by Designer Trapped in a Lawyer's Body.
  • Squeeze glue around the edges of your fabric and spread it around good with your paintbrush. Then, fold the fabric over the ring and press down. Finally, use the wooden stick that is included with the kit to push the fabric under the ring. {Sorry, I didn't get a photo of this step because both of my hands were busy}.
  • When you have finished gluing the fabric around the top ring, flip the shade over, insert the bottom lampshade ring and repeat the gluing process.
  • Finally, squeeze glue between the two short end edges of the lampshade and press them firmly together. Allow the glue to dry.

2) After your lampshade is assembled and the glue has dried, thread the wire of your pendant light kit through the finial ring on the top of the pendant light.

Finally, run glue between the two end edges on the side of the lampshade and push firmly together.

3) Hang your light! I do not provide specific electrical tutorials on my site, but I can tell you it's pretty darn easy to change a light fixture. That said, this is the very first light fixture I hung myself {Joe usually handles electrical stuff} and I made the VERY bad mistake of turning the power off only at the switch instead of at the breaker box, which did not work. I got a nice electrical shock about 10 seconds after Joe took the photo below. I wasn't smiling after that :)  But, I rallied and finished the job AFTER we turned the power off at the breaker box.

THIS IS AWESOME! You can make your own DIY pendant light using your own fabric! Full tutorial by Designer Trapped in a Lawyer's Body.

4) Lastly, if you have opted to use a twin light socket adapter {to allow for more light output}, screw it into the light socket and then screw your bulbs into place.

That's it! Isn't it GORGEOUS?!

WOW! This is amazing! Learn to make your own DIY pendant light using your own fabric! Full tutorial by Designer Trapped in a Lawyer's Body.

WOW! This is amazing! Learn to make your own DIY pendant light using your own fabric! Full tutorial by Designer Trapped in a Lawyer's Body.

WOW! This is amazing! Learn to make your own DIY pendant light using your own fabric! Full tutorial by Designer Trapped in a Lawyer's Body.

WOW! This is amazing! Learn to make your own DIY pendant light using your own fabric! Full tutorial by Designer Trapped in a Lawyer's Body.

If you enjoyed this post, be sure to check out my other DIY lighting posts, like this DIY bentwood pendant light that I made from quilting hoops:

West Elm Bentwood Pendant Knock Off by Designer Trapped in a Lawyer's Body {designertrapped.com}

 

Or this DIY industrial lighting update for our powder room:

BRILLIANT! Easy DIY update to create beautiful industrial bathroom lighting for less than $30!

Do you love my latest DIY pendant as much as I do? If so, be sure you pin it so you can remember it later!

WOW! This is amazing! Learn to make your own DIY pendant light using your own fabric! Full tutorial by Designer Trapped in a Lawyer's Body.

 

[mv_create 1 11 200 2016 key=”1″ type=”list” title=”Most Popular Projects” thumbnail=”<a href=” https designertrapped com wp content uploads diy home decor projects blog jpg a]

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

32 Comments

  1. The green pendant looks fab, I am sick of my boring white drum, floor lamp and want to vamp it up with a colour! What sort of material will I buy and maybe I can follow the steps on your video to stick it on?

  2. This is incredible, Tasha. I love the color and how perfectly it coordinates with the rest of the decor in your craft room since you used the same fabric. It’s too bad that funky light you initially installed didn’t give off enough light. It was so cool, but I can’t wait to see what you do with it instead.

  3. This is great! This one totally fits in so well with the rest of your craft room decor :) Can’t wait to see your plans for the other Ikea light!

  4. This is super cool! Your lamp turned out great! I’m glad you’re okay after that shocking bit of on the job training! ;) Seriously, sorry that happened but it is a great reminder for the rest of us. You probably saved me from having Einstein hair.

  5. Nice project! I love the fabric you chose. Maybe I missed this in the post, but what wattage does the lamp take, and how do you find the light diffusion? I’m looking for an option for my music room, and the ceiling is fairly low, so this might be a possibility. Thanks!

    1. Thanks, Sarah! The light diffusion is great! I can’t recall the wattage. We are using LED bulbs to maximize the lumens with the smallest amount of wattage. I hope that helps!